GB/T 6109.4-2008 漆包圆绕组线 第4部分:130级直焊聚氨酯漆包铜圆线
作者:标准资料网 时间:2024-04-29 19:20:47 浏览:8251
来源:标准资料网
基本信息
标准名称: | 漆包圆绕组线 第4部分:130级直焊聚氨酯漆包铜圆线 |
英文名称: | Enamelled round winding wire—Part 4:Solderable polyurethane enamelled round copper wire class 130 |
中标分类: |
电工 >>
电工材料和通用零件 >>
带绝缘层电线 |
ICS分类: |
电气工程 >>
电线和电缆 >>
电线和电缆综合
|
替代情况: | 替代GB 6109.4-1988 |
发布部门: | 中华人民共和国国家质量监督检验检疫总局 中国国家标准化管理委员会 |
发布日期: | 2008-04-23 |
实施日期: | 2008-12-01 |
首发日期: | 1985-06-17 |
作废日期: | |
主管部门: | 中国电器工业协会 |
提出单位: | 中国电器工业协会 |
归口单位: | 全国电线电缆标准化技术委员会(SAC/TC 213) |
起草单位: | 上海电缆研究所、中山信诚漆包线材有限公司、东港市电磁线厂、苏州圣利线缆有限公司、先登电工器材股份有限公司、浙江长城电子科技集团、洪波线缆股份有限公司 |
起草人: | 雷洁颜、薛水滨、鄔学良、孟祥富、姚桂华、曹恒泰、陈惠民 |
出版社: | 中国标准出版社 |
出版日期: | 2008-06-01 |
页数: | 5页 |
计划单号: | 20011004-T-604 |
书号: | 155066·1-31780 |
适用范围
GB/T6109《漆包圆绕组线》分为22个部分,本部分为GB/T6109的第4部分。本部分自实施之日起代替GB/T6109.4—1988。GB/T 6109的本部分规定了以聚氨酯树脂为基的单一漆层133级直焊漆包铜圆线的要求。本部分与GB/T6109.4—1988相比,主要变化如下:
———导体标称直径范围由原来的0.018mm~2.500mm 分别调整为0.018mm~2.000mm(1级)和0.020mm~2.000mm(2级),并取消了3级的规格范围;
———明确温度指数为130级,热冲温度为155℃,热冲击试验用圆棒直径的规定由原来的按导体标称直径范围分档改为按每一导体标称直径立项;
———增加高温下击穿电压、温度指数的性能要求;
———焊锡时间由10s/mm 和15s/mm(1级和2级)分别缩短至8s/mm 和12s/mm,最短焊锡时间由3s缩短至2s;
———增加了针孔试验项目
前言
没有内容
目录
前言Ⅰ
1 范围1
2 规范性引用文件1
3 定义、试验方法总则和外观1
4 尺寸1
5 电阻1
6 伸长率1
7 回弹性1
8 柔韧性和附着性2
9 热冲击2
10 软化击穿2
11 耐刮(导体标称直径0.250mm 及以上2.000mm 及以下) 2
12 耐溶剂2
13 击穿电压2
14 漆膜连续性3
15 温度指数3
16 耐冷冻剂3
17 直焊性3
18 热黏合3
19 介质损耗系数3
20 耐变压器油3
21 失重3
23 针孔试验3
30 包装3
引用标准
下列文件中的条款通过GB/T6109的本部分的引用而成为本部分的条款。凡是注日期的引用文件,其随后所有的修改单(不包括勘误的内容)或修订版均不适用于本部分,然而,鼓励根据本部分达成协议的各方研究是否可使用这些文件的最新版本。凡是不注日期的引用文件,其最新版本适用于本部分。
GB/T6109.1-2008 漆包圆绕组线 第1部分:一般规定(IEC60317-0-1:2005,IDT)
所属分类: 电工 电工材料和通用零件 带绝缘层电线 电气工程 电线和电缆 电线和电缆综合
【英文标准名称】:Paintsandvarnishes-Corrosionprotectionofsteelstructuresbyprotectivepaintsystems-Generalintroduction
【原文标准名称】:涂料和清漆.防护涂层系统对钢结构的腐蚀防护.一般说明
【标准号】:BSENISO12944-1-1998
【标准状态】:现行
【国别】:英国
【发布日期】:1998-11-15
【实施或试行日期】:1998-11-15
【发布单位】:英国标准学会(GB-BSI)
【起草单位】:BSI
【标准类型】:()
【标准水平】:()
【中文主题词】:卫生和安全要求;等级(质量);分类系统;钢;防护覆层;结构钢;耐腐蚀性;寿命;表面处理;防腐蚀;非合金钢;工作环境;清漆;涂料;低合金钢;结构;定义;防锈
【英文主题词】:Coatingmaterials;Coatings;Corrosion;Corrosionprotection;Corrosivestresses;Corrosivity;Definitions;Healthprotection;Materialstesting;Metalcoatings;Paints;Protectivecoatings;Safety;Steel-framedconstructions;Steels;Structuralsteelwork;Structures;Varnishes
【摘要】:1ISO12944dealswiththecorrosionprotectionofsteelstructuresbyprotectivepaintsystems.2ISO12944coversonlythecorrosion-protectivefunctionofpaintsystems.Otherprotectivefunctions,liketheprotectionagainst:—microorganisms(marinefouling,bacteria,fungi,etc.),—chemicals(acids,alkalis,organicsolvents,gases,etc.),—mechanicalaction(abrasion,etc.)and—firearenotcoveredbyISO12944.3Thefieldofapplicationischaracterizedby:—thetypeofstructure,—thetypeofsurfaceandsurfacepreparation,—thetypeofenvironment,—thetypeofprotectivepaintsystem,—thetypeofworkand—thedurabilityoftheprotectivepaintsystem.AlthoughISO12944doesnotcoveralltypesofstructure,surfaceandsurfacepreparation,itmay,byagreement,alsobeappliedtothosecaseswhicharenotcoveredbythestandard.Thevariousaspectsofthefieldofapplicationaredescribedinmoredetailin1.3.1to1.3.6.3.1TypeofstructureISO12944concernsstructuresmadeofcarbonorlow-alloysteel(e.g.inaccordancewithEN10025)ofnotlessthan3mmthickness,whicharedesignedusinganapprovedstrengthcalculation.NotcoveredbyISO12944areconcretestructuresreinforcedwithsteel.3.2TypeofsurfaceandsurfacepreparationISO12944dealswiththefollowingtypesofsurfaceconsistingofcarbonorlow-alloysteel,andtheirpreparation:—uncoatedsurfaces;—surfacesthermallysprayedwithzinc,aluminiumortheiralloys;—hot-dip-galvanizedsurfaces;—zinc-electroplatedsurfaces;—sherardizedsurfaces;—surfacespaintedwithprefabricationprimer;—otherpaintedsurfaces.3.3TypeofenvironmentISO12944dealswith:—sixcorrosivitycategoriesforatmosphericenvironments,—threecategoriesforstructuresimmersedinwaterorburiedinsoil.3.4TypeofprotectivepaintsystemISO12944coversarangeofpaintproductswhichdryorcureatambientconditions.NotcoveredbyISO12944are:—powdercoatingmaterials,—stovingenamels,—heat-curedpaints,—coatingsofmorethan2mmdry-filmthickness,—liningsoftanks,—productsforthechemicaltreatmentofsurfaces(e.g.phosphatingsolutions).3.5TypeofworkISO12944coversbothnewworkandmaintenance.3.6DurabilityoftheprotectivepaintsystemISO12944considersthreedifferentdurabilityranges(low,mediumandhigh).See3.5andclause4.Thedurabilityrangeisnota"guaranteetime".
【中国标准分类号】:G50
【国际标准分类号】:87_020;91_080_10
【页数】:16P.;A4
【正文语种】:英语
【英文标准名称】:StandardTestMethodforCigaretteIgnitionResistanceofMock-UpUpholsteredFurnitureAssemblies
【原文标准名称】:模型化装软垫的组合家俱的抗烟卷点燃性的标准试验方法
【标准号】:ASTME1352-2002
【标准状态】:作废
【国别】:美国
【发布日期】:2002
【实施或试行日期】:
【发布单位】:美国材料与试验协会(ASTM)
【起草单位】:ASTM
【标准类型】:()
【标准水平】:()
【中文主题词】:可燃性试验;可燃性;试验;装饰品
【英文主题词】:Combustibility;Combustibilitytests;Firesafety;Testing;Upholsteries
【摘要】:
【中国标准分类号】:Y80
【国际标准分类号】:13_220_40;97_140
【页数】:11P;A4
【正文语种】:英语